By TA4OHN ·
An APRS tracker is anything that works out where it is and tells the APRS network. The word covers very different devices: a handheld radio in a backpack, a mobile radio under a dashboard, a thumb-sized board on a balloon, a phone in a cup holder and a 20 euro LoRa module. They all end up as the same dot on the same map, but they differ in cost, range, battery life and what you need to know to set them up.
This guide sorts the categories, says what to look for in each, lists the settings that matter whichever one you pick, and shows how to see your own APRS tracking on aprs.world. If you are choosing hardware from scratch, read it together with our first APRS radio buyer's guide, which goes through specific models in more depth; here we stay at the level of tracker types.
Every tracker does the same three jobs:
On the radio path, nearby digipeaters repeat the packet and an iGate uploads it to the internet; the whole journey is explained in how an APRS packet travels. Because everything is public by design, anyone can then follow your tracker with no radio at all.
The simplest tracker is a transceiver that has the GPS, the TNC and the APRS firmware inside, so one box does everything.
What to look for: an internal GPS rather than an optional module, SmartBeaconing, a message screen if you want to send and receive short messages, and a real external antenna connector for mobile use. These radios also receive, so you see every station around you on the radio's own screen.
Trade-offs: price is the main one, and handheld APRS drains the battery faster than the spec sheet suggests. The rubber-duck antenna limits range; a proper whip or a car antenna makes a bigger difference than any firmware setting. Model-by-model comments are in our radio buyer's guide.
A standalone tracker has no screen and often no receiver. It is a small board with a GPS and a transmitter, or a GPS and a modem that feeds an ordinary radio. It beacons, and that is all it does.
What to look for: weight and current draw if it is going on a bike or a balloon, whether it receives (most do not, so it cannot receive messages), and whether the output power and the band suit the place you will use it. A tracker transmitting half a watt into a small antenna is heard much less far than a 5 W handheld.
Trade-offs: you configure them by serial console or a config tool, usually with no feedback beyond watching the map. Treat the first test as an exercise in finding the station on the map.
A phone already has a good GPS, a screen and an internet connection. A phone app can be an APRS tracker in two different ways:
What to look for: the right cable between the TNC and your radio model, a phone that will keep running the app with the screen off, and a way to keep it powered on a long drive.
Trade-offs: an extra device and cable, a phone battery that drains, and Bluetooth that sometimes drops. Compare the two apps in APRSdroid vs the APRS World app.
LoRa APRS keeps the APRS packet format but swaps the radio layer for LoRa on 70 cm. A tracker is typically an ESP32 board with a GPS, such as a LilyGO T-Beam, running open-source tracker firmware. The CA2RXU fork of the original OE5BPA project is the actively maintained one; our LoRa APRS guide covers frequency (433.775 MHz in most places, 439.9125 MHz in the UK), link parameters and firmware in detail.
What to look for: buy the 433 MHz variant of the board, and check that a LoRa iGate is within range of where you plan to use it, because coverage depends entirely on local iGates. The tracker transmits a tenth of a watt, runs for hours on one battery and costs very little.
Trade-offs: a LoRa tracker is invisible to ordinary 1200 baud AFSK radios and digipeaters, so it only works where LoRa iGates are installed. It suits areas with LoRa coverage and experimenters, rather than an operator who wants to be heard by the classic network from anywhere.
High-altitude balloons, model rockets and long-endurance floats are a category on their own, because weight, power, temperature and altitude are more important than a screen. They use tiny GPS-plus-transmitter boards such as the LightAPRS family, designed to be light and efficient.
The most important difference is the digipeater path: from altitude, a balloon is heard by a huge number of digipeaters, so it uses a minimal path such as WIDE2-1 or none at all, not the ground default. That, along with sounding versus pico flights and recovery, is covered in our balloon tracking guide.
Whichever tracker you pick, the same few settings decide whether it behaves well on the shared channel.
-9 is a mobile such as a car, -7 is a handheld or anything a person carries, and -10 is an iGate. See the SSID list for the others.WIDE1-1,WIDE2-1 is the modern default on the ground. Longer paths such as WIDE3-3 or WIDE7-7 flood the channel and are considered bad practice. For a balloon, use WIDE2-1 or none.0,0 is usually waiting for a fix.You do not need a radio to follow a tracker. Once your packet reaches APRS-IS, two views are available on aprs.world:
https://aprs.world/station/<CALLSIGN>, for example /station/TA4OHN-9. It shows the history and can be shared with friends and family, which is useful on a hike or a long drive.If nothing appears, the usual causes are in this order: the wrong frequency or path, no GPS fix, no iGate within range of the tracker, or, for an internet upload, a wrong passcode. Our APRS web tracker guide explains what the map shows and how to read it.
An APRS tracker is a device that gets its position from a GPS receiver and broadcasts it as an APRS packet, either over amateur radio or, in the case of a phone app, over the internet. Anyone listening, or anyone watching an APRS map, then sees the track. Trackers range from handhelds and mobile radios with APRS built in to small transmit-only boards.
Yes, to transmit. APRS runs on amateur radio bands, and even uploading your position to APRS-IS from a phone uses your amateur callsign and its passcode. Watching trackers on a map such as aprs.world needs no licence.
For a moving tracker on the ground use the path WIDE1-1,WIDE2-1. A car normally uses SSID -9 and a handheld or anything carried by a person -7. High-altitude balloons are the exception: they should use a minimal path such as WIDE2-1 or none.
Yes. Apps such as APRSdroid and the APRS World app use the phone's GPS and can send the position to APRS-IS over mobile data. To go out over radio as well, connect a KISS TNC, for example a Bluetooth one, to a radio and let the app talk to it.
Use SmartBeaconing for anything that moves: it beacons more often when you are going fast or turning and rarely when you are slow or parked. A fixed rate of once a minute or faster only fills the channel with duplicate positions.
Open the aprs.world map and search for your callsign with its SSID, or go to the address aprs.world/station/ followed by your callsign, for example aprs.world/station/TA4OHN-9. Your position appears as soon as a digipeater and an iGate, or your own internet upload, has delivered it to APRS-IS.