The APRS World app can put your own radio on the air: beacons and messages go out over RF through a KISS TNC, and everything the radio hears shows up in the app. This page lists what connects today, how, and how sure we are about each one. "Confirmed" means seen working with real hardware (for the AT-D890UV, a packet from the app heard on air); "should work" means the connection follows the same standard as a confirmed device but nobody has tried that exact hardware yet.
Connecting a radio lives in the app's RF tab, which is part of Premium. The map, station pages and reading messages are free.
The three ways to connect
Connection
Android
iPhone
Typical devices
Bluetooth Classic (SPP)
Yes
No
Handhelds with a built-in KISS TNC: AT-D890UV, TH-D74/D75, UV-PRO class radios
Direwolf on a computer or Raspberry Pi, CA2RXU LoRa iGate, any network TNC
The iPhone row is not a missing feature. iOS only lets apps talk Bluetooth Low Energy, and the KISS TNC in most handhelds is on Bluetooth Classic. On an iPhone you need a BLE TNC or a network TNC.
Confirmed working
AT-D890UV over Bluetooth Classic, Android. Messages sent from the app on 2026-08-01 were digipeated and then gated to APRS-IS by an iGate that heard them on RF (qAR in the path), which proves the whole chain from app to radio to the air.
Network TNC (TCP KISS), Android and iPhone. Direwolf's KISS port works from both platforms. This is also the iPhone route for any radio Direwolf can drive through a sound card interface.
Kenwood TM-D750A in APRS (text) mode, receive. When the radio's TNC is in its built-in APRS mode instead of KISS, the app reads the radio's text output: the stations it hears and its own GPS fix, which the map then follows (confirmed by a user in the field). The TM-D710 speaks the same text mode. Transmitting in this mode uses an experimental command mode, built from a real TM-D710 log, that is not yet confirmed on air.
Should work, not yet confirmed on air
Mobilinkd TNC3 and TNC4, PicoAPRS v4 over BLE. They implement the BLE KISS service the app looks for.
ESP32 DIY TNCs that expose KISS over the Nordic UART service.
Kenwood TH-D74 and TH-D75 over Bluetooth Classic on Android. Receiving has been seen in a field session; transmitting through KISS is not yet confirmed.
Kenwood TM-D750 over Bluetooth Classic on Android. Note that it enters KISS differently from the TH-D74 (see below).
BTech UV-PRO, Vero VR-N76, Radioddity GA-5WB over Bluetooth Classic on Android, with the radio's KISS TNC enabled.
LoRa APRS boards with CA2RXU firmware (Heltec, LilyGO and similar):
iGate: in the web config, under TNC, enable the TNC server with the KISS protocol. The board then serves KISS on TCP port 8001. In the app choose TCP and enter the board's IP address and port 8001; the phone must be on the same Wi-Fi.
Tracker: in the Bluetooth settings turn on BLE and KISS. The board then advertises the standard BLE KISS service; choose Bluetooth (BLE) in the app.
If you run one of these, we would like to hear how it went: the device, its firmware version and whether packets went both ways.
Not supported directly
Any Bluetooth Classic radio on an iPhone (AT-D890UV, TH-D74/D75, UV-PRO class). An adapter that bridges Classic to BLE, such as the open-source B.B. Link on an ESP32, should make the radio look like an ordinary BLE TNC; this is untested here.
Yaesu FTM-400, FTM-500 and FTM-300 USB ports. They carry GPS and Yaesu's own data, not a KISS TNC. Use the rear data jack with a sound card interface and Direwolf, then connect the app over TCP.
Radios whose Bluetooth is only for audio or a vendor app. The app only accepts recognised KISS services, so these are refused with a message instead of showing a link that never carries a packet.
Setup tips that save an hour
Put the radio in KISS mode. Many handhelds have a Bluetooth audio mode and a separate KISS TNC mode. In audio mode the connection opens and the received byte counter stays at zero. This is the most common cause of "connected but nothing happens".
TH-D74 / TH-D75: press [F] then [LIST] to enter KISS; the KISS interface is set in menu 983.
TM-D750: press [KEY] for the APRS soft keys, then [APRS] twice until the KISS icon shows; the interface (USB or Bluetooth) is menu 984. KISS is blocked while DV/DR mode is active.
Direwolf: keep KISSPORT 8001 in direwolf.conf and connect the app to the computer's IP address on port 8001. Our Direwolf setup guide covers the rest.
Test properly. A link that opens is not a link that carries data. Leave it connected while a station you know is beaconing nearby, or key a packet from a second radio, before deciding it does not work.
Frequently asked questions
Can I use my TH-D74 or AT-D890UV with the APRS World app on an iPhone?
Not directly. Those radios offer their KISS TNC over Bluetooth Classic, and iOS only lets apps use Bluetooth Low Energy. On an iPhone, use a BLE TNC, a network TNC over Wi-Fi (TCP KISS, for example Direwolf on a computer), or an adapter that turns Classic into BLE such as B.B. Link.
Does the app work with LoRa APRS boards?
It should, but it has not yet been confirmed on a real board. A CA2RXU LoRa iGate with its TNC server enabled offers KISS on TCP port 8001, which the app connects to over Wi-Fi. A CA2RXU LoRa tracker with Bluetooth set to BLE and KISS offers the same BLE KISS service the app looks for.
The app says connected but nothing arrives. What is wrong?
Almost always the radio is not in KISS TNC mode. Many handhelds have a Bluetooth audio mode and a separate KISS TNC mode; in audio mode the link opens but no packet data ever flows. Switch the radio's Bluetooth or TNC setting to KISS, reconnect, and wait for a station you know is beaconing.
Do I need Premium to connect a radio?
Yes. Connecting a KISS TNC and transmitting over your own radio is part of the RF tab, which is a Premium feature. The map, station pages and reading messages are free.