By TA4OHN ·
Packet radio is how amateur radio learned to send data. Instead of a voice or a continuous stream of Morse, the information is chopped into short, self-contained frames. Each frame carries the callsign of the sender, the callsign of the destination, the payload and a checksum, and each one is sent over an ordinary radio channel as a short burst. If you have ever watched a station appear on a map a few seconds after it keyed up, you have watched packet radio working.
Voice is a continuous stream and the listener does the error correction. Data is different: one flipped bit can change a number or a callsign. Packet radio solves that by sending data in frames, each with a header that says who sent it and who it is for, followed by the payload and a frame check sequence (FCS), a CRC that lets the receiver discard anything that arrived damaged.
The result has three properties that explain most of what follows:
Amateurs began experimenting with this in the late 1970s and early 1980s. The link-layer protocol they adopted was adapted from the commercial X.25 world and named AX.25 - the "A" is for amateur. It is still the protocol on the air today.
AX.25 defines the frame format: a flag byte at each end, an address field holding the destination, the source and up to eight digipeater addresses, a control byte, a protocol ID (PID), the information field and the FCS. Callsigns are stored with an SSID from 0 to 15 so one operator can run several stations.
AX.25 can be used in two ways:
For a field-by-field walk-through of the frame, the address encoding and a real APRS packet, see our guide to the AX.25 protocol and APRS packet format.
On VHF the standard packet modulation is 1200 baud AFSK, Audio Frequency Shift Keying following the Bell 202 modem standard. The modem generates two audio tones - 1200 Hz for one bit value and 2200 Hz for the other - and feeds them into the transmitter's microphone input. The radio carries them as normal narrowband FM. On the receive side, the audio from the speaker or discriminator goes into the modem, which turns the tones back into bits.
This is the speed APRS uses worldwide on 144.390 MHz in the Americas and 144.800 MHz in Europe and Africa (the full list is in APRS frequencies by country). It is slow by today's standards, but it works through any FM voice radio, tolerates mediocre signals, and a position report is only a few dozen bytes anyway.
On HF, packet uses a slower 300 baud AFSK modulation, used on single-sideband radios. HF packet is rare today; APRS on HF is one of the few places it survives.
For more speed, amateurs use 9600 baud FSK in the form designed by James Miller, G3RUH. Instead of audio tones, the modem sends a scrambled baseband signal that directly modulates the transmitter, and it needs a radio that handles the data signal properly. That is the catch: a typical handheld's microphone and speaker path filters and shapes the audio, which destroys a 9600 baud signal. Radios built for it have a dedicated 9600 baud data port (a mini-DIN "data" jack is the common sign), or can be modified.
Where it is used, 9600 baud makes sense for high-traffic links and for backbones between nodes. It is not used for ordinary APRS on 144.390 or 144.800 MHz, which is strictly 1200 baud. Some satellite and specialist networks use 9600 baud; always follow the local convention for the frequency you are on.
The device that does the modem work is the TNC, a terminal node controller. In its classic form a TNC is a box with a modem, a microprocessor and firmware that assembles AX.25 frames. It plugs into the radio on one side and a computer terminal on the other. The TNC designs published by TAPR (the Tucson Amateur Packet Radio group) became a de facto standard in the 1980s and were cloned widely; commercial TNCs from Kantronics, MFJ and others followed, and many APRS radios still embed a TNC today.
Early TNCs offered a command-line terminal. The modern interface is KISS ("Keep It Simple, Stupid"), a minimal serial protocol that strips the TNC down to a dumb modem. The computer builds the whole AX.25 frame, and the TNC just wraps it in simple delimiters, modulates it and keys the radio. In the other direction it hands every decoded frame up to the computer unchanged. All the intelligence - sessions, APRS, maps - lives in software on the computer or phone.
KISS is the glue of the modern packet world. Software modems, hardware TNCs such as Mobilinkd and NinoTNC, LoRa APRS firmware and nearly every APRS client speak it, over a serial port, USB, Bluetooth or a TCP socket. If you remember one acronym from this guide, make it KISS.
Once computers were fast enough, hardware modems became unnecessary. A soundcard modem does the modulation and demodulation in software, using the computer's audio input and output as the analogue interface to the radio. The two you will meet most often are:
What you need besides the software is an audio interface that connects the computer to the radio and keys the transmitter (the PTT line). Options range from a plain USB sound card and a home-made cable to purpose-built interfaces; the Direwolf guide covers them. Many people on Linux or Raspberry Pi use Direwolf; our APRS software roundup shows what to run on top of it.
For many years "packet" meant connected-mode services. They are worth knowing because you will still run into them.
Packet BBS. A bulletin board system is a computer connected to a radio. You connect to it with AX.25 in connected mode, read bulletins, and leave and fetch private messages. BBSs forwarded mail to each other over the radio network, a store-and-forward arrangement that carried messages across a country, hop by hop, long before email was common. Popular BBS software includes FBB and the BPQ family.
Nodes and NET/ROM. A single VHF radio only reaches so far. Packet nodes (software such as BPQ, and the older NET/ROM and ROSE network layers) are stations that relay your connection onward: you connect to the nearest node, tell it where to go, and it builds a path across a network of other nodes. This was packet radio's answer to wide-area networking before the internet. Node networks were often linked with 9600 baud or faster backbone radios.
Winlink. Winlink is a radio email system. Operators send and receive messages through gateway stations that connect to the internet. Winlink began on packet radio and today also runs on other modems, but VHF and UHF packet gateways are still part of it, and it remains a staple of emergency communication. Our APRS-side guide notes that Winlink gateways even show up as objects on the APRS map, and the WLNK-1 service can be queried by APRS message.
The one packet application that kept growing is APRS, the Automatic Packet Reporting System. It solves a problem the internet did not: showing where people and things are, over radio, in real time, with no infrastructure other than radios.
APRS is built from the same parts you have just read about. A radio, a TNC (internal, external or software), AX.25 UI frames at 1200 baud AFSK on a shared frequency. What is different is the philosophy. Instead of connecting to a destination, each station simply broadcasts a short, self-describing frame - a position, a weather report, a message - and everyone in range decodes it. Digipeaters repeat frames to extend range, and iGates carry them to the internet, which is why a packet sent from a handheld shows up on the aprs.world live map seconds later. We trace one packet through the whole chain in how an APRS packet travels from RF to APRS-IS, and the beginner overview is What is APRS?.
If you want to try packet radio today, APRS is the easiest way in. A handheld with a built-in TNC, a phone and a KISS TNC, or a computer running Direwolf all get you on the air, and the map shows you immediately whether it worked. From there you can explore the rest of the packet world, because the same TNC and the same software modem that carry APRS can also connect to a BBS or a node.
Packet radio is amateur radio data communication in which information is split into short frames, each carrying source and destination callsigns and an error check, and sent over a normal radio channel. On VHF and UHF it almost always means AX.25 frames modulated as audio tones on an FM radio, at 1200 or 9600 baud.
Yes, but mostly through its best-known application. APRS is packet radio, and tens of thousands of stations beacon every day. Classic connected-mode packet with BBSs and node networks has shrunk since the internet arrived, although some BBSs, nodes and Winlink packet gateways are still operated by volunteers.
Packet radio is the general technology: AX.25 frames, TNCs and radios. APRS is one application built on top of it. It uses unconnected UI frames in a fixed format to share positions, weather, telemetry and short messages with everyone in range, while classic packet radio mostly used connected sessions between two stations.
You need a modem, but it does not have to be a hardware TNC. A soundcard modem such as Direwolf or UZ7HO SoundModem turns a computer's audio interface into a TNC, and many handhelds and mobiles have a TNC built in. A phone app can also act as the modem.
1200 baud AFSK (Bell 202 tones) is the standard on VHF and is what APRS uses. 9600 baud G3RUH FSK is the faster option on VHF and UHF but needs a radio that passes the data signal without audio filtering. On HF, packet runs at 300 baud.
To transmit, yes: packet radio uses amateur bands, so you need an amateur radio licence and your own callsign in every frame. Receiving and decoding packets does not need one in most countries.